.jpg)
FSP460-60PFN
| · | Active PFC circuit |
| · | High efficiency |
| · | Low noise and ripple |
| · | Output over voltage protection |
| · | Short circuit protection on all outputs |
| · | Resettable power shut down |
| · | Approved by UL 1950, CSA 22.2 Level 3, IEC 950, TUV EN60950, NEMKO CB & CE |
| · | Internal 12 VDC ball bearing fan provided |
| · | Complies with FCC part 15 subpart J class B 115 VAC operation and CISPR 22 230 VAC operation |
| · | 100% burn-in under high ambient temperature (50° C) |
| · | MTBF above 100,000 hrs at 25° C |
| · | 100% Hi-pot & ATE tested |
| · | Line input fuse protection |
| · | Full range 100 ~ 240VAC |
Input Characteristics
| · | Voltage: 95-132 VAC or 180-264 VAC switch-select |
| · | Frequency: 47Hz to 63Hz |
| · | Input current: 10A(RMS) for 115 VAC, 6A(RMS) for 230 VAC |
Specification
| · | Temperature range: operating 0° C ~ 50° C; Non-operating: -20° C ~ 65° C |
| · | Temperature coefficient: 0.01%/° C |
| · | Transient response: Output voltage returns in less than 1 ms max. at a 25% load change |
| · | Hold up time: 18ms minimum at 115V/60Hz. 18ms minimum at 230V/50Hz |
| · | Dielectric withstand: Input/output 1800VAC for 1 second, input to frame ground 1800 VAC for 1 second |
| · | Humidity: 5 ~95% RH |
| · | Efficiency: 65% Min., 70% typical, at full load |
| · | Power good signal: Power on delay time 100 ms to 500 ms, off delay 1 ms minimum |
| · | Overload protection: 150% Max. |
| · | Inrush current: 80A max. for 115 VAC or 100A max. for 230 VAC at 25° C ambient cold start |
| · | With Fan Noise Killer |
| · | Over voltage protection: |
| +3.3V | output: | 4.5V max |
| +5V | output: | 6.5V max |
| +12V | output: | 15 V max |
Remote ON/OFF Control
| · | The power supply shall accept a logic open collector level which will disable/enable all the output voltage. (exclude +5V stand by) |
| · | As logic level is low, outputs voltage were enable. |
| · | As logic level is high, outputs voltage were disable. |
|
MINIMUM LOAD |
MAXIMUM LOAD |
CROSS REG. |
LINE REG. |
RIPPLE & NOISE |
|
|
*+3.3V |
0.4A |
27.0A |
+5% ; - 4% |
± 1% |
50mV P-P |
|
+5V |
3.0A |
29.0A |
+5% ; -4% |
± 1% |
50mV P-P |
|
+12V CPU |
1.0A |
16.5A |
+5% ; -4% |
± 1% |
120mV P-P |
|
+12V I/O |
1.0A |
15.0A | +5% ; -4% |
± 1% |
120mV P-P |
|
-5V(optional) |
0.0A |
0.3A |
± 10% |
± 2% |
120mV P-P |
|
-12V |
0.0A |
0.8A |
+9% ; -4% |
± 2% |
120mV P-P |
|
+5Vsb |
0.0A |
2.0A |
+5% ; -4% |
± 1% |
50mV P-P |
*+3.3V
& +5V total output not exceed 200 watts.
*+3.3V & +5V & +12V total output not exceed 440 watts.
*Dimension: 140(L) x 150(W) x 86(H) mm